I can't put to work my Openvpn ESXi bridge to work.
Could someone show me it's ifconfig output, so I could figure what is wrong in my config ?
Or could someone help me ?
I'm developer public school teacher, not network specialist. But I need this bridge to make some tests.
I installed Openvpn Access Serveur Virtual Appliance in my ESXi box.
Then my /etc/network/interfaces :
Code: Select all
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address 200.53.114.43
netmask 255.255.255.240
gateway 200.53.114.33
#Private Network
allow-hotplug eth1
iface eth1 inet static
address 172.1.50.9
netmask 255.255.255.240
# gateway x.x.x.x
I put VPN mode to : Layer 2, but no Bridge Name to Join (it says it's optional).
I need to bridge from home to LAN 172.1.50.0 network, so I put in Advanced VPN -> Server Config Directive the line :
Code: Select all
ifconfig-pool 172.1.50.12 172.1.50.12 255.255.255.240
In my Openvpn ESXi bridge, the ifconfig give me :
Code: Select all
as0t0 Link encap:Ethernet HWaddr fe:ff:ff:65:1f:00
inet6 addr: fe80::fcff:ffff:fe65:1f00/64 Scope:Link
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:1223 errors:0 dropped:0 overruns:0 frame:0
TX packets:1138 errors:0 dropped:1 overruns:0 carrier:0
collisions:0 txqueuelen:200
RX bytes:118971 (116.1 KiB) TX bytes:122625 (119.7 KiB)
asbr0 Link encap:Ethernet HWaddr 00:0c:29:ae:ba:74
inet addr:200.53.114.43 Bcast:200.53.114.47 Mask:255.255.255.240
inet6 addr: fe80::20c:29ff:feae:ba74/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:4861 errors:0 dropped:0 overruns:0 frame:0
TX packets:2774 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:541219 (528.5 KiB) TX bytes:498187 (486.5 KiB)
eth0 Link encap:Ethernet HWaddr 00:0c:29:ae:ba:74
inet6 addr: fe80::20c:29ff:feae:ba74/64 Scope:Link
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:41472 errors:0 dropped:0 overruns:0 frame:0
TX packets:4003 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:22860963 (21.8 MiB) TX bytes:617626 (603.1 KiB)
eth1 Link encap:Ethernet HWaddr 00:0c:29:ae:ba:7e
inet addr:172.1.50.9 Bcast:172.1.50.15 Mask:255.255.255.240
inet6 addr: fe80::20c:29ff:feae:ba7e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17364 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1438884 (1.3 MiB) TX bytes:468 (468.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:31 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13074 (12.7 KiB) TX bytes:13074 (12.7 KiB)
If I keep mode to : Layer 2, but put Bridge Name asbr0, ifconfig give me :
Code: Select all
eth0 Link encap:Ethernet HWaddr 00:0c:29:ae:ba:74
inet addr:200.53.114.43 Bcast:200.53.114.47 Mask:255.255.255.240
inet6 addr: fe80::20c:29ff:feae:ba74/64 Scope:Link
UP BROADCAST RUNNING PROMISC MULTICAST MTU:1500 Metric:1
RX packets:42295 errors:0 dropped:0 overruns:0 frame:0
TX packets:5015 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:23005868 (21.9 MiB) TX bytes:820754 (801.5 KiB)
eth1 Link encap:Ethernet HWaddr 00:0c:29:ae:ba:7e
inet addr:172.1.50.9 Bcast:172.1.50.15 Mask:255.255.255.240
inet6 addr: fe80::20c:29ff:feae:ba7e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:17631 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1460972 (1.3 MiB) TX bytes:468 (468.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:31 errors:0 dropped:0 overruns:0 frame:0
TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:13074 (12.7 KiB) TX bytes:13074 (12.7 KiB)
I spent some days without success. I suppose I don't have all the knowledge to fully understand the problem.
I'm teacher for public school and need this bridge for my students to learn some programing...
Please if someone can help.
Thanks a lot.
Vincent MARECHAL